Tutorials:Simple Mesh Replacement In Blender-Finishing The Map - Revision history

Cmomoney at 16:24, 23 January 2013

2013-01-23T16:24:25Z

Cmomoney: Created page with " {|style="border-spacing:8px;margin:0px -8px" |- {|style="border-spacing:8px;margin:0px -8px" |style="width:50%;border:1px solid #cef2e0;background-color:#C9C8E6;vertical-alig..."

2013-01-23T15:45:41Z

Created page with " {|style="border-spacing:8px;margin:0px -8px" |- {|style="border-spacing:8px;margin:0px -8px" |style="width:50%;border:1px solid #cef2e0;background-color:#C9C8E6;vertical-alig..."

New page

{|style="border-spacing:8px;margin:0px -8px"
|-
{|style="border-spacing:8px;margin:0px -8px"
|style="width:50%;border:1px solid #cef2e0;background-color:#C9C8E6;vertical-align:top;color:#000"|
{|class="MainPageBG" width="100%" cellpadding="2" cellspacing="5" style="vertical-align:top;background-color:#C9C8E6"

|-
|style="color:#000"|

==Finishing the Map==
Now on to the rest of the cylinder.
===Step 18===
In the 3D View, Press NUM2 until you can see the bottom of the cylinder. In the UV/Image editor, zoom(NUM-) out so you can see the other islands, then put your cursor over the other circle island and press L to select it. As you did the with the top, use zoom, G , S, and R to get the island in the middle of the other little blue square on the image.
[[File:Mappingrest1.jpg|600px|center]]

===Step 19===
Zoom back out and select and use L to select the remaining piece of the cylinder. Use G and S to get the to get the move and size the island so the top and bottom of it are just above and below the lines on the sides part of the image. In the 3D view, press CTRL+NUM1 to go to Back view. Then press S, then X to constrain to the x axis and scale the island so the lines meet on the back of the mesh.
[[File:Mappingrest2.jpg|600px|center]]

|-
!align="left" style="font-weight:normal" |[[Tutorials:Simple_Mesh_Replacement_In_Blender-Mapping_The_Top|<<Back]]
|align="right"|[[Tutorials:Simple_Mesh_Replacement_In_Blender-Bones_Triangulating_And_MeshSwap|Next>>]]
|}
|}
|}

@@ Line 13: / Line 13: @@
 ==Finishing the Map==
 Now on to the rest of the cylinder.
-===Step 18===
+===Step 19===
 In the 3D View, Press NUM2 until you can see the bottom of the cylinder. In the UV/Image editor, zoom(NUM-) out so you can see the other islands, then put your cursor over the other circle island and press L to select it. As you did the with the top, use zoom, G , S, and R to get the island in the middle of the other little blue square on the image.
 [[File:Mappingrest1.jpg|600px|center]]
-===Step 19===
+===Step 20===
 Zoom back out and select and use L to select the remaining piece of the cylinder. Use G and S to get the to get the move and size the island so the top and bottom of it are just above and below the lines on the sides part of the image. In the 3D view, press CTRL+NUM1 to go to Back view. Then press S, then X to constrain to the x axis and scale the island so the lines meet on the back of the mesh.
 [[File:Mappingrest2.jpg|600px|center]]